LM386 stereo amplifier in bridge 2 watts

Here is LM386 stereo audio amplifier circuit, 2 watts. Using 3 ICs in a bridge model. It is cheap and easy to builds for a beginner.

In normal we use LM386 as a small amplifier. It can give an output power is 500mW to 700mW. But this circuit is special. The designer set the circuit is the bridge mode in a stereo system.

So, they can be saved one IC. And have power about 4 times of general OCL amplifier.
Max power of this circuit is 2 watts + 2 watts.

A basic of amplifier

The characteristics of the general amplifier, Figure 1. Connect an output directly to a positive of a speaker and the negative terminal to the ground.

normal amplifier system


Figure 1 the normal amplifiers

And, suppose we set the gain of a power amplifier is about 2 times.

If an input signal is 1 volt, the output equals:

1-volt x 2 times = 2 volts

Remember Figure 1. What is more?

Bridged amplifier working

Look: Figure 2

We add the amplifier 2 into the amplifier section 2.

What the difference is between Figure1 and Figure 2?
The main feature.

  • Figure 1—The gain is about 2 times only.
  • Figure 2— The gain is as much as 4 times.

Which is better?

You begin interested in Figure 2, right? We called a bridge amplifier form.

Sure its power is higher loud than the first model. Some called the BTL model (Bridge output Transformerless). Advantage, not require the high voltage power supply. And can provide high power magnification.

How Working of bridge amplifier mode


Figure 2: Basis of BTL- Bridge amplifier model

The sound from the speakers in Figure 2 is 2 times of Figure 1.

Some may wonder why bridge amplifier is high power than normal?

Both amplifiers are the same gain. But amplifier 2 works inverting phase of amplifier 1.

Imagine, it is similar we connect both batteries, different polarity. The total voltage is both batteries.

But in contrast.

Do not connect the output together. It is a short circuit until both amplifiers run too much power. Sure, they damaged.

Not only that. If we can get LM386 to build a stereo amplifier with bridge mode.

Sound good, doesn’t it?

See in the circuit below.

How circuit work

In Figure 3 is fully of LM386 stereo circuit, 2 watts.

LM386 amplifier stereo 2W


Figure 3: LM386 stereo amplifier in bridge 2 watts

Let me explain why it works in simple ways. Here is the step-by-step process.

  • Apply 6V power supply to the circuit.
  • Then, enter audio signals into the input.
  • Adjust VR1 to turn volume up-down.
  • Three IC1, IC2, and IC3 are the heart of the circuit, each IC includes resistors and capacitors connected with the appropriate values.
    To give power up to 700mW to 1W (from datasheet).
  • Both IC1 and IC2 work together to increase the sound output to the loudspeaker, in the left channel.
  • At the same times, IC2 and IC3 will work together, too. To amplifier to the right speaker. Equal to wattage is about 2 watts.
  • We will see using 3 ICs each unit is 1 watt. But it was a combination of all the 4 watts. Profits of 1 watt.

Hey! This is low watts for you, right?
Look:

TDA2030 Stereo Amplifier with PCB

The parts you will need

IC1-IC3: LM386, Mini Amplifier

Resistors 0.25W, tolerance: 5%
R1, R3: 47K
R2, R4, R5: 10 ohms
R6: 1K

Electrolytic Capacitors
C1, C8: 4.7uF 50V
C2, C5, C9: 22uF 16V
C4, C7, C11, C12: 470uF 10V

Ceramic capacitors
C3, C6, C10: 0.047uF 50V

VR1: 10K (A) Potentiometer
LED1: LED as you like.
Switches, PCB, Box, wires and more.

How to builds

First of all, find all parts as the list in the circuit diagram.
This circuit use can build on the Universal PCB. Fast and Cheap.

However, if you want to use PCB layout see below.

The actual size of single-side PCB layout.

The actual size of single-side PCB layout.

05-the-components-layouts

Component and wiring Layout

Here are a few related posts you may find helpful, too:

13 thoughts on “LM386 stereo amplifier in bridge 2 watts”

  1. It’s a weird circuit; I’ve been toying with this little ic’s in the pursue of more power, and did a bridge amp which sounds right with the correct speakers; I used 8″ 8 ohm sensitive speakers ( big magnet) and sounded amazingly loud for the size of the devices; with smaller ones the sound is plain deceiving; the first time I tried the circuit was with 8″ 25 ohm from an intercom and the loudness is unbeileibely loud. This little things have hard times at this pace so should be heathsinked; for my tests with 8 ohm I used 1/4″ aluminium plate with 3″ by 4 1/2″ size ( approx) mounted the ic’s carefuly against it used stripped pcb and built the cct. You may surprise the sound you can get from this little things. Someday I’ll build an entire “mini” audio system with the modules I built; I know not if I’m using 8 or 25 ohm speakers but should be well done TL enclousures with separate tweeters; The devices were fixed with a complementary piece made with the same material fixed with 1/8″ stove screws with lots of care; you won’t want to brake the ic’s either bend the aluminium locking parts.

    Reply
  2. Hi I am from Iran Reza
    I wanted to remove particulate filter circuit metal detection and measurement of the volume of metal in the ground and without errors thanks

    Reply
  3. I’d seen this diagram and i build it.. luckily i made it but what speaker that suits in this mini amplifier?i want to use 1 woofer and 2 tweeter can you email me please..thanks

    Reply
  4. I want to purchase 200 peices audio amplifier pcb with audio jack & usb connector for giving 5v power to circuit. please contact me on 9146032723

    Reply
  5. This is Brilliant!
    And i don’t see any reason why the principle can’t be used with other OpAmp-like Power ICs as well.
    Thanks for sharing this idea.

    Berty.

    Reply
  6. Oh, wait a moment!
    What’s up with R1 and R3? Aren’t they almost shorting the input signal to ground?
    Shouldn’t they be at least 47K instead of just 47 ohm?

    Reply

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.