# 0-30V variable Power Supply at 3A

This is a 0-30V Variable Power Supply circuit diagram. I recommended this. Because you can adjust an output voltage of 0V to 30V, at 3A current, and overload protection.

Also, It is a high-efficiency regulator using IC regulator, UA723, and power transistor, TIP3055. So, it is small laboratory DC Power Supply in inexpensive cost.

Best for who is finding circuits: 0-12V and 0-24V variable power supply circuit diagram. Because It is high current, normal parts, a new circuit design.

## Why should make 0-30V variable Power Supply

• Modern design—I used to show you the old circuit below, also using LM723. But it powers a current just 2A. And It uses 2N3055 power transistor. So, It is difficult to make. But this use TIP3055 instead. It is slim so easy to install on a heatsink.
• Output voltage—voltage output adjustable: 0-30VDC
• Current maximum—all range of output voltage it can power current up to 3A
• Inexpensive—if you compare with old circuits. this is cheaper than them.
• Need part—you should use a transformer: 12-0-12V 4A for full current up to 3A.

## How does it work

Oops! Here is too difficult. Look at…
0-30v variable power supply. or

LM350 voltage regulator

As Figure 1 circuit diagram. The order of operation is interesting.

• Reduce AC voltage—the AC main to a transformer to reduces the AC high to AC low voltage. See below, how to set the voltage as you want.
• Rectifier AC to DC—Low AC voltage flows through the bridge diodes(D1 through D4) set. They rectify  AC to DC pulse voltage.
• Unregulated DCV—C1 is a filter capacitor to the pulsating voltage into a steady direct current (DC). Before, send to…
• DC regulator circuit—the voltage comes to IC1 and some parts. They keep the output voltage is constant. Even the load will draw current too many, the voltage is still stable.If you want to read more detail of LM327 circuits you can visit. Datasheet!But the current out of pin 11 of IC1  is very weak. They need increasing current.
• Increase current–two transistors TR1 and TR2 are connected in Darlington mode, so a lot of gains.
• Detect overload—Sometimes it is too much current that the transistor and other parts tolerate it.
You look at parallel resistors(R1 to R5) are reduced to 0.2 ohms to detect overload current.

If
the current exceeds 3A. The voltage across these resistors more than 0.6V. Also, The voltage at the base-emitter of TR3 is 0.6V, making it works. Between its collector-emitter likes, a switch closed. It also connects with the base-emitter of TR1. It makes TR1 reduce working, the current is lower. Then, TR2–power transistor stops working too. Thus, the output is low current, this circuit is safe.
• Adjustable voltage—You rotate VR1 to change the output voltage between 0V and 30V.
• Special voltage selector—Adjusting VR1 at low voltage is difficult. Such as 0-12V, 0-10V, and more. But this is special, you can select a range of voltage in 2 steps, low and high, with SWITCH in a circuit. Low: 0-12V and High: 0-30V. If you cannot imagine Read below!

### Let’s build them

First of all, get the electronics components.

#### Parts you will needs

We may buy them at electronics stores near you or online to get parts.

IC1: uA723-HIGH PRECISION VOLTAGE REGULATOR
Q1: BD140-80V 1.5A PNP Transistor
Q2: TIP3055, 60V 15A, high-Speed Switching Silicon transistor
Q3: CS9012, 40V 0.5A PNP Bipolar Transistors
D1-D4: 1N5401, 100V 3A Rectifier Diodes
Electrolytic capacitors
C1: 4700uF 50V
C3: 100uF 50V

Ceramic Capacitors
C2: 680pF 50V
C4: 0.1uF 50V
0.5W 5% Resistors
R1-R5: 1 ohms
R6: 50 ohms
R7, R9, R12, R13: 100K,
R8: 2.7K,
R10: 10K,
R11: 5K,
VR1: 5K, Potentiometer

Others
T1:12V-CT-12V, 4A transformer
Heatsink, PCB, Wires, and more…

Note: Here are KITS that I bought from a local store. If you want to save time, it can be ordered through Amazon. READ MORE!

Then, Assemble the components on PCB.

It starts with the lowest parts first, to be beautiful. Easy assembly To start with, followed by a diode, resistor and, respectively height and so on. As the image below soldering lowest electronic components.

Be careful! Some components have polarity like electrolytic capacitors, diodes, transistors, etc. They require correct placing. If they are the wrong polarity. They will get destroyed from reverse voltage.

The components layout and wiring of this 0-30v variable power supply project.

We assembled all parts completely on PCB.

This project uses AC power so we must be careful about high voltage.

Finally, we have made this project so successful.

Applications

The connecting “12” and “0” will be through a selector switch.

For 2 selector;

• Use voltage 0-12V at “0”
• Use voltage output 0-30V at “12,12” the voltage minimum is 0.3V to maximum is 33 volts.
This way makes the transistor, not overheat.

The output we should connect a 3A fuse in series before to use.

## Testing

We test this project. As the video step by step.

1. Apply the AC power then turn on power switch ON.
2. Select Switch to 0-12V Before then Rotate the knob VR1 fully the left.
3. Measure voltage at the output point, then rotate the VR1 slowly to right, the output voltage starts is 0.3V or 300mV to 16VDC maximum.
4. Toggle switch to “12-24V” then measure the voltage again 330mV to 32 volts.
5. Setting the output is 12V, then Apply a 12V 50W as the load.
6. Measure the current output when load 12V is 3A maximum.
7. Temperature measurement of transistor operation.

## How to solve circuit not works

If you made this project but it did not work. You do not worry. It is not a problem. It is a process of your electronic learning. You should have fun solving it.

Here are some basic guidelines for you.

First—No load, No power to this circuit. And Check and Check again with slowly. Surely, something is wrong.

Second—If you check all is correct. You try to power to the circuit again. Then, measure the voltage at.

• TP A(Test point)—It should read voltage about 33VDC. If it is not like this. You should check the unregulated voltage again. Which they include a transformer, bridge diodes, and C1.
• TP B—Also voltmeter should read about 33VDC. But it is zero or lower voltage. Show that parallel resistor, R1-R5 are broken.

Third—check the circuit again. even pins of IC1.

Equivalent Transistors
CS9012—If you Cannot find CS9012 transistor you may use equivalent transistor is BC327 PNP transistor. But Different pinout positions between the Emitter and collector.

CS9012 datasheet : http://www.mouser.com/ds/2/149/SS9012-117759.pdf
Ice = 500mA max, Vce = 40max

BC327 Datasheet : http://www.mouser.com/ds/2/149/BC327-30422.pdf
Ice = 800mA, Vce = 40Vmax

If you want the better circuit to look here!

## Variable power supply

Sharing is caring!

## GET UPDATE VIA EMAIL

I always try to make Electronics Learning Easy.

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Subscribe
Notify of

plz upload pcb for this supply

Iqbal

Where I buy this pcb board

Ron

Do you have the whole power supply as a kit with PC BOARD?

MR OHM 1970

What A Handy Dandy Little piece Of Test Gear To Have Around Your Test Lab!! Thanks MOMENAME

Gokhu

hi..how to design this circuit..how to calculate the value ..will you tell me how to design this power circuit

Nguyễn Văn Tiến

Hello !!!
His name is Tien, Vietnam .We himself as he was the Student attending Electronics industry, I have enjoyed watching your product, I want to embark on the implementation of this product, You can ask yourself Printed circuit Board (PCB) of you. If possible I would like to thank you very much 🙂

Another idea for a bench or lab supply, that is even less expensive, is to re-use the power supply unit (PSU) from an old computer. The following link gives detailed instructions for converting and reusing the PSU from a disused or old computer

The transformer in the parts list is 12-0-12V, could you explain how the circuit can produce up to 30V DC Supply, thanks

ElecCircuit.com

Thanks for your answer. Please check voltage across C-4700uF is 33V-35V DC. and check circuit again slowly. It is worked!

Jesrel

Would you please share your PCB for this project? Thank you! From Philippines…

daniel

hi. tks for all but could you share your PCB for this nice and usefull projet?

Ibrahim

hi. Thank for all but could you share your PCB for this nice and usefull projet?

Ritcheboy

Hi sir I always checked your projects and I really love it can you give me the PDF file or pcb layout ang parts list plssss
I want to make this

[email protected]

Sanjay

Hi, any equivalent for CS9012 as nowhere it’s available here in India.

Dibos

Is it okey to use diode(4007)

ElecCircuit.com

You may use a diode 1N5402 better in 3A 100V.

Yvon

Hello sir i need a voltage schemes regulate 0-30 + –

bob

Hello, I’m new to the site, I wanted to groped with all of you for the simplicity and precision with which you do these things for nothing simple for a novice like me. You are the most interesting site I’ve ever found on electronics, and I’ve visited many, thank you for what you do.

Lander Ignacio

Is it okay to replace the transformer to 12V 3A or 14V 4A

ElecCircuit.com

Hi, Lander Ignacio
You are welcome.

Yes, you can use 14V CT 14V or 28V output transformer.
It is 39V DC at C1. And the output voltage regulator will rise up to 35V approx.

If you have any results. Please back to here again.

Thanks.

Anon

How to modify this for higher current .i.e. 5A instead of 3A?

George

Does it have anything if I use a simple 28V transformer?

Donatus

I want to add a display for the variable voltage and one for the current. I need you to help me with how to set it up.

MAriana

Hi, could you tell me how to add a short circuit protection?