Power Amp Super Bridge 120W by IC TDA2030 Reviewed by momename on . This be Super Bridge 120W Power Amplifier by IC TDA2030 for you like the circuit amplifies that use the integrated circuit. and Transistor BD249 or TIP31 or TIP This be Super Bridge 120W Power Amplifier by IC TDA2030 for you like the circuit amplifies that use the integrated circuit. and Transistor BD249 or TIP31 or TIP Rating:
You Are Here: Home » Amplifiers » Power Amp Super Bridge 120W by IC TDA2030

Power Amp Super Bridge 120W by IC TDA2030

This be Super Bridge 120W Power Amplifier by IC TDA2030 for you like the circuit amplifies that use the integrated circuit. and Transistor BD249 or TIP31 or TIP41 or C1061 and BD250 or TIP32 or TIP42 or A671. It is nice circuit and easy to use.

Schematic-diagram of-power-amp-super-bridge-120w-by-ic-tda2030
Schematic diagram of Power Amp Super Bridge 120W by IC TDA2030

pcb-layouts-of-120W-amplifier-using-tda2030
PCB layout and Components layout of 120W supper bridge Power Amplifier using TDA2030

This circuit is designed by using TDA2030A circuit as driver to power transistor output to applied to out up 30 watt.
- then take both circuit to bridge together, makes we have the power output up to 4 times and have even maximum power output is 200Watt.

May don’t be defeated because this circuit give the electric power about 120W that load 2 ohm. When see the circuit will think use important equipment be. Must use power supply source that be appropriate about +15V and -15V that current 2Amp. Besides should use heat sink at have the size is appropriate IC TDA2030 and Q1-Q4 BD249,BD250 for see the circuit has already. Build easy must not fine decorate anything. Request a friend has fun Power Amp Super Bridge 120W by IC TDA2030 please sir.

- The advantage of this circuit, the voltage of the power supply is low (compared to other circuits. Watts are equal in size), so I used the low voltage capacitor, smaller, and cheaper.
- As can be seen from the circuit, we enter a signal input at pin 1 is side single. With pin 1 of IC2 (TDA2030) is connected to ground, And the output signal fed back to the inverting pin (pin 2) of IC2, Allow us to signal with opposite phase, input to the amplifier is one automatically.

How to build

Soldering Electronic Components to the right, onto the PCB as shown in Figure 2. Then install the power transistor to the heat sink. By Vice insulating sheet mica. To prevent a short circuit on the heat sink neatly.
When certain everything must be right, it was the power supply to the circuit, in order to use it, without having to adjust the circuit.

Detail of circuits

Q1,Q3_________BD250___PNP POWER TRANSISTORS(25A,125W)
Q2,Q4__________BD249____NPN POWER TRANSISTORS(25A,125W)
D1,D2,D3,D4____1N4002____Diode 1A 100V
IC1,IC2_________TDA2030A__18W HI-FI AMPLIFIER AND 35W DRIVER
R1,R7,R11,R13__2.2 ohm____Resistors 1/2W
R2,R3,R12______100K______ Resistors 1/4W
R4,R8__________2.2K_______ Resistors 1/4W
R5,R6__________3.3K_______ Resistors 1/4W
R9,R10_________1 ohm______ Resistors 1/2W
C1_____________0.0015uF 50V___ Polyester Capacitor
C2,C3,C4,C5,C7_0.022uF 50V___ Polyester Capacitor
C6_____________10uF 16V_____ Electrolytic Capacitors

Power amplifier with PCB easy to build

Bass guitar super bridge amplifier 200 watt.

100 watt DC servo amplifier by Power MOSFET

The cheap 100 watt transistor power amplifier project

The main amplifier 50 watt OCL by LF351-2N3055-MJ2955 with PCB

Power Amplifier OCL 50W by Mosfet (K1058 + J162)

Power Amplifier OCL 40W by 2N3055+MJ2955



Comments (20)

  • mostafagordy

    Hi
    my english is poor … sorry .
    I read this article.
    It is possible to make this amplifier circuit with MOSFET Transistors

  • Ghulam Mustafa

    i have made this circuit but it did not worked what the problem is there i do not know. however i shall try again to check it up. then will comment.

  • Ghulam Mustafa

    i have made the circuit bridge120W by i.cTDA2030 as per the circuit and pcb given but it does not work why? i do not know all connections and wiring has been checked could any help me in this matter

  • Ghulam Mustafa

    i have made the circuit bridge120W by i.cTDA2030 as per the circuit and pcb given but it does not work why? i do not know all connections and wiring has been checked could any one help me in this matter

  • tiep

    Pin 2 of two IC TDA2030 mustn’t connect Power.The Power will be connected with pin 5 of two IC TDA2030.Negative (pin 2) pole and positive pole(pin 1) connect with Audio signal…

  • Akhil

    Friends the given circuit diagram is wrong

  • Joel

    What is. Correct way?

  • Joel

    Anyone know the proper connections.???.

  • Joel

    The problem is on the 2030 chip you have pin 3 and 5 reversed . Pin 1 is + and pin 5 should be on the same side in the schematic. Pin 2 is – and pin 3 should be on the same side in the schematic. Easy mistake

  • ravi

    pls give me a 5.2 channel circuit
    simple ic transistor based
    with power supply

  • Joel

    Whis it? In the parts list you show c2,3,4,5,7 as 0.022uf but in the schematic you show them as 0.22uf. There is a big difference. Also in the parts list you have c1 and c6 as 0.0015 uf 50v and 10 uf 16v but the schematic shows them as both 0.22 uf . Can u pleas write me with the correct info? What else is wrong with the project? Help please. I bought all the parts but can’t assemble until I know.

    Thank u

  • GS_TURNA

    Can we use the tda2050 place of tda2030, what watts of that type amp

  • saikat

    how many inch speaker it take load

  • Biplov

    There is little mistake in the circuit.if the output is 120watts then the power transistor getting DC+ voltage via TDA2030 ? It must be in parallel to 2.2ohms supply. it will not work in 6volt DC. It requires 12V/7Amps free from rippling DC.

  • SAHEER KM

    TRANSISTOR COLECTOR LEG

  • Nayanjyoti

    yeh… i hav made dis circuit…
    the sound quality is nice.
    but the bass reflex is very poor..
    i replace both TDA2030A IC to TDA2050..
    and added one 1mF caps at the (+ve) input signal
    and added one 2000mF caps at the output signal..
    now the bass and the output power is increased to more… then before it has.

  • auxtics

    Hi everybody,
    The circuit has many problems and it should be rectified before building this.
    So if you are searching for tda2030a or tda2050 Integrated Circuits then you may visit the links below
    Here is the complete Youtube video for building a stereo amplifier based on tda2030a great IC
    http://adf.ly/11UCT6
    and here is the complete PCB board and notes for building this great project
    http://adf.ly/11UAAx
    For more information contact us.

Leave a Comment

Copyright © 2015 www.eleccircuit.com

Scroll to top