Many Electronic circuit projects in simple ways of learning

TDA2030 transistor amp circuit with PCB

If you are looking for a power amplifier for listening in a small house. This may be a good choice for you. If you are looking for a power amplifier for listening in a small house. This may be a good choice for you. Because of the higher power than a mini amplifier. With an output power of 20W at 8Ω  or 30W at the 4Ω speaker.

I called that TDA2030 transistor amp. As it uses two transistors to increase more output power.

Although it is great. But you do not worry. It still is easy to build, without any adjustment.

The working principle

As shown figure the circuit, you see three main components. They are like three soldiers, TDA2030 and two transistors (TIP41TIP42 or 2SC1061,2SA761 or BD908BD907). Their helping to increase the signal up there.

Others components are useful as well. However, I will explain them to you learn as follows.

The OTL amplifier listen comfortably by TDA2030 and TIP41+TIP42


Figure 1.  TDA2030 transistor amplifier circuit 30 watts output

When we enter the power supply and sound signals into this circuit. The capacitor C1 will prevent DC voltage through input. So, the sound signals can get into the pin 1 of IC1 easily.

Also, this circuit uses a single power supply that has two terminals are positive and Ground(negative).

So, we need to connect two resistor R1, R2, and C2 to divide the voltage by half. And, the R3 matches the input IC1.

In the circuit, the gain of IC1 is set to 14. Because it is a non-inverting amplifier pattern there.

Transistors boost up IC amplifier

The output signal flows out of pin 4. But it still is low. We need helping of the transistors. Both transistor Q1(TIP41) and Q2(TIP42) increase more power up.

How do they work? Resistor-R6 passes the current to supply IC1 of the positive terminal. Also, Resistor R7 passes the current to IC1 of the negative terminal.

When the many currents flow through R6 and R7. Then, the voltage drop across them exceeds 0.6V. Which is bias voltage to Q1 and Q2. So, they help to pass more current from the supply to output.

After that, the higher output signal flows the loudspeaker through C8.

While this circuit can protect the loss of high frequency that output to the loudspeaker by R8 and C7.

Also, both diodes D1 and D2 are used to prevent the return voltage from the speaker not to interfere with the IC1, Q1, and Q2.

If none of these two diodes may damage the device, including money in your pocket separately.

And, both filter capacitor the C7 and C8 smooth the power again before it is provided to the circuit there.

 


How to build and setting

The Familiar thing in building the project is to make PCB (printed circuit boards) as Figure 2.

PCB layout of TDA2030 transistor amplifier circuit 30w
PCB layout in actual-size of single-sided Copper

And, buy electronic components from stores list below.

When you finish the PCB and list. Next, you solder them on PCB
as shown in Figure 3

Components layout of TDA2030 with transistor boosting amplifier OTL

Components layout of TDA2030 transistor amplifier project

 

I believe you know the process of creating a good project.
You should Solder the components onto PCB, the low end to high end will be a beautiful view.

Make sure the device is a correct terminal before soldering.

This project uses IC1, Q1 and Q2 should use the big size heat sink to install them with together as shown in figure 2.

Components you will needs
R1,R2,R3: 56K, 0.25W Resistor
R4: 3.3K, 0.25W Resistor
R5: 30K, 0.25W Resistor
R6,R7: 1.5Ω,  0.5W Resistor
R8: 1Ω , 0.5W Resistor
C1,C3,C6,C7: 0.22uF 63V, Polyester Capacitor

Electrolytic Capacitors
C2: 47μF 25V
C4: 10μF 25V
C5,C8: 2,200uF 50V

Semiconductor devices.
D1-D2: 1N4001 or 1N4002
Q1: PNP transistor 2SA671 or TIP42 or TIP32 or BD908
Q2: NPN Transistor 2SC1061 or TIP41 or TIP31 or BD907
IC1: TDA2030
Sheets of mica, Cooling pad (Heat sink)

How to use

First, need to use the DC power supply of 24V to 30V of 1A for MONO.

Then take the audio source as the tuner, cassette or a CD player to test it.

Finally, Connect a 20W 8Ω the loudspeakers to the output.

For those who want to listen in stereo, you need to build up to two circuits. And change the power supply of 2 A. It can be used.

If you want a good circuit you may use 24V 2A regulated power supply. It is great.

Now, it is time to listen to a crystal clear sound from your created yourself.

Related Posts


JLCPCB - Only $2 for PCB Protytpe(Any Color)

With 600,000+ Customers Worldwide, 10,000+ PCB Orders Per Day

Up to $20 shipping discount on first order now: https://jlcpcb.com/quote

This Post Has 18 Comments

  1. It’s really very difficult in this full of activity life to listen news on Television, so I simply use web for that purpose, and obtain the newest news.

  2. Hi , I just did this amp. but this is not true: The sound signal output is amplified to pin 4 of IC1 And to boost (increase) to increase with Q1 (TIP41) and Q2 (TIP42).
    -Q1 is TIP42, and TIP41 is Q2, please be cereful with transistors.

  3. hello the actual size of PCB ?

  4. מחפס לירכוש מעגל אלקטרוני להגברת רמקולים למחשב שיהיה בה מעגל טרבל בס וליום 20wtקיט להרכבה עצמית

  5. Why are all the 2030 amps so wrong? Is anyone able to have the correct schematic for the bridged amp using the tip 31 and tip 32????????

    Someone help. I already bought the components .. Very sad here..

  6. i did this one with a input voltage of 30v but i think the ampere is low (500mA) and the output is getting distortion and i have a 50w speaker 4ohm… what to do ??? i have no idea !!.

  7. – Forget this schematics. If you won cheep and easy build nice amplifier use TDA7294 witch is 90W into 8ohm +/- 30V power supply. I already build one. If you need correct schematic and PCB just e-mail me I’ll send you pictures and all you need.
    – If you won bridge schematic for TDA2030 (35W max into 8 ohm) e-mail me and I’ll send you all you need. [email protected]

  8. Where C5 in PCB ?

  9. I BUILT THIS AMP WITH TIP41/42 TRANSISTORS SINCE THE BD COUNTERPART IS NOT AVAIL IN COLOMBO.BUT THE OUTPUT IS ONLY 13WATTS. EVERY THING IS DONE AS PER CIRCUIT. VOLTAGE SUPPLIED IS 35VOLTS WITH 4AMPS IN STORE.IAM NOT GETTING .6V ACROSS THE TWO 1.5OHMS RESISTORS TO FIRE THE TWO OUTPUT TRANSISTORS,ONLY .4 V. PLS ADV ME WHAT THE PROBLEM COULD BE.MANT TKS

  10. I finish my amplifier few day’s ago. Everything working fine , sounds very good , low heat disipation and low distorsion. Using TDA2030A with TIP41C and TIP42C. Transformer is 4A / 24V AC , so 24V x 1.3 = 31V DC and 6800 mF cap. Tested on 4 ohms speaker / 50 W. Great sound ! For any help and pictures: [email protected]

  11. hey man this is awesome, it has no distortions. Works like magic!! thanks

  12. i buit this circuit n i faced a new kind of problem.
    i made 2 channels with the same schematic except i used 2.2ohm /0.5W instead of the 1.50hm.
    One of the channel works quite well…very good sound indeed!!!..but for the other channel 2.2ohm resistor from pin 5 is getting fried when i powering the circuit with 24volts 1amp supply with filter cap of 4700uf.
    Plz help me out…m in a serious mess…
    Heres my email:[email protected]
    for any kinda help.
    Thanks to all in advance.

  13. i built this amp but getting distortion any one with a better idea should kindly mail me at
    [email protected]

  14. Fiz um amplificador como o esquema. Más quando alimento ele e ponho no volume maximo, pega fogo no resistor de 1,5ohm, e os dois transistores queimam. Usei TIP31/32.
    Estou alimentando o circuito com +-35v 2a. Seria o problema a tensão de alimentação acima de 30v?

  15. I’ve success made this TDA + Power Transistor curcuit.I use TDA2050 + TIP3055/TIP2955.Single supply setup at 48VDC/3A for the curcuit.I use 2pcs 24VDC/3A + 24VDC/3A ITE adaptor in series.
    Base on standard TDA2050 single supply schematic.Added 10 Ohm 2Watts X 6pcs on parallel for (1.66 Ohm).All 12pcs 10 Ohm 2 Watt for both ground and positif rail.Output capasitor i use 50v/2200uF X 2pcs also on parallel to get 4400uF for speaker out.
    Sound awesome the bass impact with woofer 6.5″ x 2 pcs on series to get 8 Ohm config.I use 2 pcs altec lansing VS4621 woofer.Make my glass windows in my room rattt…krrr.rrr….krrrr….shaking on 70% > volume up.!! 😀

  16. On TDA2030 + power transistor above..What does C6 do to this curcuit?Im noob any explaination?my power resistor (R6) on PNP got overheat by adding C6.So i remove it then it balance on both power resistor (R6) and (R7).Im bit comfuse on this,Do i make anywrong connection?I follow the schematic above..C6 make problem on my curcuit,why?

  17. The circuit is great, but rather scared about the Two
    1.5 ohm resistors. I have one ohm – 1 watt. Transistors shouldn’t blow!

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Close Menu