MJ15004 | Electronic Project Circuits

Posts Tagged ‘MJ15004’

10A DC Supply FIX Regulated by IC 78XX and MJ15004

Today a friend of me visits at a house. He leads old equipment come to give very plentiful and tell beg for DC power supply 10A circuit. That be simple please , when I sees the equipment that him has had already. Then take this circuit see use 78XX integrated circuits. Have many the number and Transistor power number M15004 that can enhance current. Get tall arrive at 10A.The important aspect is must use Transfermer that be appropriate give current 10A More than. And use C-Filter 10000uF sizes go up with. The detail is other see in the circuit has leisurely sir.

Power Amp OCL 100W by Transister MJ15003,MJ15004

This Circuit Power Amp OCL 100W by Transistor.It old circuit,but very well amplifier schematic.
Use transistor MJ15003 and MJ15004, power supply +38V,-38V 3A.
Output power 100W at Speaker 8OHM.

Circuit Power Amp OCL 100W by Transistor MJ15003,MJ15004

PCB Power Amp OCL 100W by Transistor MJ15003,MJ15004
Source : pk kit circuit

Power Amplifier OCL 300W HIFI by transister

For
many application there’s no substitute for sheer power- low efficiency
speakers, outdoor sound systems, or maybe you like the full flavour of
the dynamic range of a high power amp. Whatever your requirement-this
super power module should fit the bill. How it works: The amplifier can
be divided into three separate parts.

These are : the input stage, which
consists of Q1-Q9 , a high gain, low power driver; the output or power
stage- witch only has a voltage gain of four but enormous power gain;
and the power supply. The input stage is a complementary -differential
network, each ”side” with its own current source. Each transistor in
this stage is run at a collector currant of about 0.7mA. Emitter resistors
are employed to stabilize the gain and improve linearity. The output of
Q1-Q5 drives Q7 and Q9. The latter are virtually two constant-current
sources run about 7mA collector current. With an input signal these “current”
sources are modulated out of phase – the collector current of one decreases
while the other increases. This configuration provides quite an amount
of gain. In between the bases of these two transistors is Q8, the thermal
sensing-bias transistor. The voltage across Q8 may be adjusted by TR1,
thus setting the quiescent bias current for output stage. The output stage,
Q10-Q11, Q13-Q14 and Q16-17, has a gain of about five, set by R44 and
R28 plus R29. Diodes D4 and D6 prevent reverse biasing of Q10 and Q11
(otherwise the output would be limited). Protection of the output transistors
is provided by Q12 and Q15 which monitor both current and voltage in the
output transistors and bypass the base current if the limit is exceeded.
Frequency stabilization provided by capacitors C6, C11, C12 and the RC
networks R31/C10 plus R46/C15. Frequency response of the amplifier is
set by C1 and C7 (lower limit), C6 sets the upper frequency limit. If
you want use the Protection DC and Balance/Bridge circuits. All the transistors
that are inside the interrupted line are placed on an aluminium corner
and he screwed on a suitable heatsink. The transistors Q7,Q10,Q11, Q8,
Q9, Q13,Q14,Q16 and Q17 placed on this aluminium corner, with suitable
isolation from this

Part
List

R1-19= 1Kohm 5W R34-35= 0.1ohm 5W C14-17= 100uF 100V
R2-3= 4.7Kohm R36-43= 39ohm C15= 100nF 250V polyester
R4-5= 22ohm R37-42= 5.6Kohm 1W Q1-2-3= BC547
R6-14= 10Kohm R38-41= 220ohm 5W Q4-5-6= BC557
R7-8= 1Kohm R39-40= 0.1ohm 5W Q7-11-12= BD140 or BC640
R9-23*=10K ohm R44-45= 0.1ohm 5W Q8= BC549
R10= 10ohm *see circuit sch. R46= 4.7ohm 2W Q9-10-15= BD139 or BC639
R11-13= 2.2Kohm R47= 100ohm Q13-14= MJ15004
R12= 22Kohm C1= 2.2uF 25V Q16-17= MJ15003
R15-16= 22ohm C2-6= 330pF ceramic TR1= 2K2 Trimmer
R17-18= 4.7Kohm C3-8= 100uF 100V F1-2= 5A Fuse Fast
R20-25= 390ohm C4-9= 100nF 250V D1-3= 5.1V 0.5W Zener
R21= 6.8Kohm C5= 100nF 100V polyester D2= 62V/5W Zener or 47v and 15V
in series
R22= 4.7Kohm C7= 100uF 25V D4-5= 1N4004
R24-26-33= 220ohm C10= 1.5nF 100V polyester L1=10 turns diameter 1mm in
15mm diameter tube
R27-32= 100ohm 1W C11-12= 1.5nF 100V polyester
R28…31= 100ohm C13-16= 100nF 250V polyester *Use R23=6k8 for 4 ohm loudspeakers

.

SPECIFICATIONS

POWER OUTPUT 200W rms/8 ohm
310W rms/4 ohm
800W rms/8 ohm (Bridge mode)
FREQUENCE RESPONSE 20HZ-20KHZ +/-0.5dB
INPUT SENSITIVITY 1V for 200W/300W
HUM AND NOISE -105dB
THD <0.1%>

Source
:: http://users.otenet.gr/~athsam/power_amp_300w.htm