Making Simple Buzzer circuit

Let’s make the electronic buzzer circuit in simple ways. But useful well worth and the price is lower than 1$. By using just a 9-volt battery only. So without worrying about electrical leakage or an electric shock from 220V to a buzzer. Unless also has LED will glow. Show that the circuit a normal operation as well.

Make Simple Electronic Buzzer circuit

Simple buzzer circuit

From the circuit in figure 1 will see that we use both transistors, which are matched pair transistors(CS 9012, CS9013), which works together with a few resistors, and capacitors. In as the oscillator circuit build sound signal frequency.

simple electronic buzzer circuit diagram using two-transistor

Figure 1: simple electronic buzzer circuit diagram using two-transistor

By has both resistors- R=1.2K and C=0.047uF to set the output frequency. Which can change slightly the value of both components, so the output sound changed. However, from the experiments, this value will be the best frequency.

The components list

Q1: CS9012: 50V 0.8A PNP Transistor
Q2: CS9013: 50V 0.8A NPP Transistor

*** for transistor please read the note:

C2-0.047uF 50V_Ceramic Capacitors

Electrolytic Capacitor
C1-33uF 25V or 47uF 25V or 10uF 25V

0.25w 5% resistors

R1-50K or 56K
R3-120Ω or 100Ω
R2-1.2K or 1K

LED: any color as you want
Piezo speaker,
9-volt battery Or 9V power supply circuit
PCB, and others.

Transistors Equivalent

You can use any transistor number for example

NPN type: 2SC1815,BC547,2N3904
PNP type: 2SA1015,BC557,2N3906

But Position legs mismatch please be careful. as Figure below.

compare position legs transistors mismatch

Making Buzzer circuit

This project uses a few components and is easy. So you can assemble them on a perforated board or universal PCB board.

But if you would like to build PCB. You can also see the copper foil track layout of this project. (actual size) the prototype board as Figure 2 and Figure 3 is the components layout.

Copper PCB layout transistor simple buzzer
The bottom layout or Single-sided PCB layout

component layout transistor simple buzzer
Components layout of simple buzzer circuit

This circuit use a voltage supply of 9V. So, normally it can use 6V to 12V.

All resistors use size ¼W.

Loudspeaker use size of 2 inches 8 ohms 0.25 W

You can listen to it in the video below.

Increase the buzzer loudness

A Simple loud buzzer circuit (trembling sound) is creating a kind of ring circuit that provides a strange sweetness of general bell. It uses all-transistor so easy to builds and cheap, suitable for bedroom or a private room good or may be adapted into a bell. Listening to children play leisure. In addition melodic sound then. Also has LED light flashes with the beat shakiness of the sound as well.

The working principle

In the circuit, we will divide into two sectors work together. Firstly, as low frequency oscillator. Secondly, will be sound frequency oscillator.

On this second section include two transistors are CS9012, CS9013 are set as the audio frequency oscillator has out of 1200 Hz to a speaker. And some current from transistor will through to LED.

trembling sound buzzer circuit using transistors


Trembling sound buzzer circuit

So, when the sound signal occurs. The LED1 will also glow. But The latter circuit will connect through pin C of Q2. So, if Q2 not conducted current, this circuit will not generate sound.

In that first section. There may be Q1 and Q2 connect together with R, C as the multivibrator oscillator.

They generate low frequencies of 5 Hz. So, Q2 will conduct and stop current with speed of about 5 Hz per minutes. It causes the second section generates a frequency out of sounds is approximated, sonorous, clear melodic quite vividly.

Building louder buzzer

This circuit use power supply of 9V. All resistors use ¼ W of size. The speaker 8 ohms size 2 inch 0.25 watts.

This project use a few components. So we can assemble on the universal PCB board. But we can make a PCB layout see as below. (LEFT)

Then, the wiring for circuit wiring and various components can view of the example in Right.

Watch out! carefully for is the polarity of the electrolytic capacitors and Pin of the transistors are not an error.

single-sided-pcb-layout-and-components-layout-of-this-projects

Single-sided PCB layout(left) and The components layout of this project. (Right)

The components List

0.25W Resistors, tolerance: 5%
R1: 1K
R2: 5K
R3: 2.7K
R4: 68K
R5: 1.2K
R6: 330 ohms

Semiconductors
Q1: 2SCC1815, C945, C458, NPN transistor
Q2, Q3: CS9013 or equivalent_NPN transistor
Q4: CS9012 or equivalent_PNP transistors

Electrolytic capacitors
C1, C2: 10uF 16V
C3: 1uF 16V

C4-0.047uF 50V, Ceramic

LED1: Any color as you want.
SP1: Speaker 8 ohms 2 inch 2 watts

Download This

All full-size images of this post are in this Ebook: Elec Circuit vol. 2 below. Please support me. 🙂

Siren Sound using transistors

13 thoughts on “Making Simple Buzzer circuit”

Leave a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.